Suitable cable: 0.6/1kV three core low voltage cable (cross-section 10-300mm ²), compliant with IEC 60502-2 and GB/T 12706 standards, designed specifically for building power distribution, industrial equipment, and renewable energy scenarios.

Suitable cable: 0.6/1kV five core low-voltage cable (3-core+neutral wire+ground wire), with a cross-section of 4-300mm ², in compliance with IEC 60502-2 and GB/T 12706 standards, designed specifically for building power distribution, industrial equipment, and renewable energy scenarios.

Suitable cable: 0.6/1kV four core low-voltage cable (3-core+neutral wire+ground wire), with a cross-section of 25-400mm ², in compliance with IEC 60502-2 and GB/T 12706 standards, designed specifically for building power distribution, industrial equipment, and renewable energy scenarios.

Compatible cable: YJV/YJLV single core cross-linked cable (cross-section 25-300mm ²), voltage level 8.7/15kV, in compliance with GB/T 18889 and IEC 60502-2 standards, designed specifically for indoor scenarios such as substation cabinets and data centers. Electrical testing: Power frequency withstand voltage of 45kV/30min without breakdown, lightning impulse withstand voltage of 105kV (GB/T 3048.8);

Compatible cable: 8.7/10kV dual core cross-linked cable (cross-section 25-240mm ²), in compliance with GB/T 12706 and IEC 60502-4 standards, specifically designed for railway signaling, mining equipment, and industrial power distribution scenarios. Red/yellow identification kit (IEC 60446 standard) reduces the risk of misconnection by 90%. Waterproof sealing: IP67 protection level

Compatible cable: 10KV three core low voltage cable (3+1 core structure), with a cross-section of 25-400mm ², complying with IEC 60502-2 and GB/T 12706 standards, pre installed with yellow, green, and red color identification sleeves and blue neutral line identification, designed specifically for building power distribution, industrial equipment, and renewable energy scenarios. Quick installation: Propane spray gun low-temperature shrinkage (110-130 ℃), single set installation time ≤ 4 minutes, 50% higher efficiency than traditional cold shrinkage technology.

Compact design: The outer diameter is reduced by 40% (Φ 90mm) compared to traditional porcelain sleeves, suitable for KYN28 switchgear; Intelligent identification: pre-set red/yellow/black phase identification sleeve, reducing the misconnection rate by 95%. Electrical testing: Lightning impulse withstand voltage 125kV (GB/T 3048.8), 1.2/50 μ s waveform; Mechanical strength: Axial tensile strength ≥ 180N (IEC 61479), withstand mechanical vibration of switchgear (5-200Hz/3g)

As a key connecting component between 35 kV and below cross-linked cables (XLPE) and oil immersed cables In a certain offshore wind farm in the East China Sea (case in 2023), the HSY-35-3.2 type intermediate joint operated for 2 years in an environment with a salt spray concentration of 5%, maintaining an insulation resistance of ≥ 1000M Ω (tested according to GB/T 3048.5) and no partial discharge phenomenon; The 35kV single core indoor terminal adopts an ultra-thin design (wall thickness 3.2mm ± 0.3mm), suitable for KYN61 switchgear, with an outer diameter of only Φ 110mm after installation (48% smaller than traditional epoxy conduit);

Specially designed for YJV/YJLV series cables (suitable for 50-400mm ² cross-section), using an integrated stress cone and composite insulation structure (inner semiconducting layer+XLPE+anti trace layer), passed GB/T 18889-2021 type test, with a long-term use temperature range of -55 ℃ to 105 ℃, an aging life of up to 20 years, a radial shrinkage rate of ≥ 50%, a longitudinal shrinkage rate of<5%, and a shrinkage temperature of 110 ℃ to 140 ℃.

Specially designed for YJV/YJLV series cables (suitable for 50-400mm ² cross-section), using an integrated stress cone and composite insulation structure (inner semiconducting layer+XLPE+anti trace layer), passing GB/T 18889-2021 type test, with temperature resistance of -40 ℃~105 ℃, lightning impulse withstand voltage of 170kV, and three-phase electric field deviation<8%. The diameter is reduced by 35% compared to traditional solutions, making it suitable for compact spaces in substation switchgear.

Provide a full range of 10KV/20KV/35KV heat shrink terminals and intermediate joints (models HSY-35-3.1 to 3.3), suitable for cable cross-sections of 50-400mm ², in compliance with GB11033 standard, with a radial shrinkage rate of ≥ 50%, temperature resistance of -55 ℃~105 ℃, and a 20-year aging life. Through hydrogen sulfide resistance, explosion-proof (ISO 80079-36), and salt spray testing, it is applied in fields such as power, petrochemicals, and rail transit. Typical cases include 8000 hours of trouble free operation of offshore drilling platforms. Support scanning for traceability, provide free cable cross-section matching tools, increase installation efficiency by 65% compared to traditional solutions, and reduce overall costs by 57%.