Suitable cable: 26/35kV three core cross-linked polyethylene (XLPE) cable, with a cross-sectional area of 50-400mm ², complying with IEC 60502-4 and GB/T 12706 standards, designed specifically for outdoor scenarios of offshore wind power, substations, and industrial high-voltage transmission and distribution.

Compatible cables: 21/31kV, 26/35kV single core and three core cross-linked polyethylene (XLPE) cables, with a cross-sectional area of 50-400mm ², in compliance with IEC 60502-4 and GB/T 12706 standards, designed specifically for flammable and explosive environments such as petroleum, chemical, and mining.

Suitable for connecting single core three core cross-linked power cables with voltage levels of 21/31.5KV and 26/35KV, serving the functions of sealing, insulation, and stress dissipation. Especially suitable for flammable and explosive places such as petroleum, chemical, mining, etc.

It is suitable for 0.6/1 KV PVC,XLPE,rubber insulation single-core,two-core,three-core,four-core,five-core electric cable.Suitable cable: 0.6/1kV three core low voltage cable (3-core+neutral wire), with a cross-section of 4-300mm ², in compliance with IEC 60502-2 and GB/T 12706 standards, designed specifically for building power distribution, rail transit, and industrial equipment.

Suitable cable: 0.6/1kV three core low voltage cable (cross-section 25-400mm ²), compliant with IEC 60502-2 and GB/T 12706 standards, designed specifically for building power distribution, industrial equipment, and renewable energy scenarios. Propane spray gun low-temperature shrinkage (90-120 ℃), single installation time ≤ 2 minutes, efficiency increased by 75% compared to cold shrinkage technology;

Adapter cable: YJV/YJLV series three-core cable (section 25-400mm²), voltage class 10kV, in line with GB/T 18889 and IEC 60502-2 standards, designed for indoor scenarios such as substations and data centers. Electrical test: power frequency voltage 42kV/5min no breakdown, lightning impact voltage 95kV (GB/T 3048.8); Mechanical strength: Axial tensile strength ≥180N (IEC 61479), withstand the mechanical vibration of the switch cabinet (5-200Hz/3g acceleration). Compact design: the outer diameter is 45% smaller than the traditional porcelain sleeve (Φ85mm), suitable for KYN28A-12 switchgear; Intelligent identification: Preset red/yellow/green phase identification ring (according to IEC 60446), error rate is reduced by 98%.

Adapter cable: YJV/YJLV series three-core cable (section 25-400mm²), voltage class 10kV, in line with GB/T 18889 and IEC 60502-2 standards, designed for indoor scenarios such as substations and data centers. Electrical test: power frequency voltage 42kV/5min no breakdown, lightning impact voltage 95kV (GB/T 3048.8); Mechanical strength: Axial tensile strength ≥180N (IEC 61479), withstand the mechanical vibration of the switch cabinet (5-200Hz/3g acceleration)

10KV/20KV/35KV full voltage level heat shrink terminals and intermediate joints (including HSY-35-3.1 to 3.3 models), suitable for cable cross-sections of 50-400mm ², covering scenarios such as electricity, petrochemicals, and rail transit. IP68 waterproof (0.1MPa water pressure verification)+non-linear stress control (field strength ≤ 2.5kV/mm)+radiation cross-linked polyolefin insulation (dielectric strength ≥ 30kV/mm). Propane spray gun shrinks in 3 minutes, with an efficiency improvement of 65% compared to cold shrinkage technology; Weighing only one-third of the traditional porcelain terminal, it is suitable for small spaces such as switchgear and tunnels.